Charles 3648-80 Betriebsanweisung Seite 1

Section 360−381−S02Equipment Issue 2Third Printing, October 2006Telecommunications Group2006 Charles Industries Ltd.All rights reserved. Printed in U

Section 360−381−S0210Table 3. Remote NMS Address Lookup TableLocal NMS Address 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16Local ADDRESS IDswitch setting0

Section 360−381−S0211Message area. Check this area for messages other than alarms, includ-ing the response to status requests made from the STATUS men

Section 360−381−S02125.1 Set T1 ParameterSelect Settings"Set T1 Parameter to open the primary T1 card (T1-S) parameter settings.Once you have fin

Section 360−381−S0213Parameter DescriptionPossible ChoicesOperation Mode Normal Mode Normal T1, or when used with the secondary T1 card allowsfor Drop

Section 360−381−S0214Parameter Possible Choices DescriptionLBO (Line Build-Out)Short Haul: 0 to 660 ft. Pre-equalization of signal for line conditions

Section 360−381−S02155.3.1. FXO Parameters (for 3658-80 12 Channel FXO/DPT Unit)Figure 8. FXO Parameter SettingsParameter Possible Choices Descriptio

Section 360−381−S02165.3.2. FXS Parameters (for 3657-80 12 Channel FXS/DPO Unit)Figure 9. FXS Parameter SettingsParameter Possible Choices Descriptio

Section 360−381−S02175.3.3. E&M Parameters (for 3652-80 12 Channel E&M Unit)Figure 10. E&M Parameter SettingsParameter Possible Choices D

Section 360−381−S02185.3.4. OCU-DP Parameters (for 3632-80 12-Channel Office Channel Unit – Data Port)Figure 11. OCU-DP Parameter SettingsParameter P

Section 360−381−S02195.3.5. DSU-DP Parameters (for 3633-80 12 Channel Data Service Unit—Data Port)Note: Availability ofsome optionsdepends onthe data

Section 360−381−S0221. GENERAL1.1 Document PurposeThis document describes how to install and use the Intelligent Channel Bank (ICB) Network Management

Section 360−381−S0220Stop Bit 1 or 2 Select 1 or 2 stop bits for async mode only.7/8 Bits Mode 7 or 8 Select 7 or 8 data bits for async mode only.5.3.

Section 360−381−S02215.3.7. 56/64xN Parameters (for 3634-80 6-Circuit 56/64xN Data Service Unit—Data Port)Figure 14. 56/64xN DSU-DP Parameter Setting

Section 360−381−S02225.3.8. Ethernet Router Parameters (for 3641-80 and 3648-80) Figure

Section 360−381−S0223Use the following steps to change time slot allocation. Time slots and chassis slots must be unallocated beforethey can be alloc

Section 360−381−S0224Use the following steps to change the time slot mode:Step Action System Response1. Select the mode you want the time slot set to.

Section 360−381−S0225Step Action System Response1. Select Status"Retrieve Inventory Data. Opens a dialog box asking you to select the cardyou wan

Section 360−381−S02267. TESTING7.1 Loopback TestUse the Loopback tests to troubleshoot problems when an alarm is reported on the card.7.1.1. Loopback

Section 360−381−S0227Step System ResponseAction3. Check the box beside the channel number(s) youare using.4. Select OK Initiates the loopback or relea

Section 360−381−S0228Figure 22. FXO/FXS Card Loopback7.1.4. Loopback of OCU-DP CardUse the following steps to perform the OCU-DP card loopback.Step A

Section 360−381−S0229Figure 23. OCU-DP Card LoopbackNote: OCU-DP far and near end loopback generators do not operate when the ICB is equipped with a

Section 360−381−S0232.2 Installing the SoftwareUse the following steps to install the software:Step Action1. Insert the CD containing the NMS software

Section 360−381−S02307.1.5. Loopback of DSU-DP CardUse the following steps to perform the DSU-DP card loopback.Step Action System Response1. Select Lo

Section 360−381−S02317.1.6. Loopback of ISDN CardUse the following steps to perform the ISDN card loopback.Note: Loopback is only available for ISDN c

Section 360−381−S02327.1.7. Loopback of 56/64xN CardUse the following steps to perform the 56/64xN card loopback.Step Action System Response1. Select

Section 360−381−S02337.1.9. 1 kHz 0dbm0 Test ToneDuring this test a continuous tone is present until released. Use the following steps to perform the

Section 360−381−S0234Step System ResponseAction3. Click Retrieve. Displays the data in a graph (see Figure 29).4. Click Close when you are done lookin

Section 360−381−S0235Figure 30. 15-minute PM Data8. MAINTENANCEUse the Maintenance menu to perform some basic, full-system functions.8.1 Audible Cut

Section 360−381−S0236Figure 31. Clock Settings8.4 Firmware DownloadThis selection is for factory use only.8.5 Config UpdateConfig update is a functio

Section 360−381−S0237Step System ResponseAction3. Enter a file name The file name appears with the extension .dat4. Select Save The file is saved.8.5.

Section 360−381−S0238Figure 33. Create New User9.2 Delete UserUse the following steps to remove a user from the system:Step Action System Response1.

Section 360−381−S0239List of currentusersFigure 35. Main screen showing a list of current users9.5 Channel MemoUse the channel memo dialog box to sto

Section 360−381−S0243. EQUIPMENT STATUSOnce the software is started, it searches for the status of any ICB previously added to the NMS equipment data-

Section 360−381−S024010. VERSIONSelect to see the version of ICB software installed.11. TECHNICAL ASSISTANCEIf technical assistance is required, conta

Section 360−381−S02418. Open the local ICB software.9. Perform steps 2−7 above. All alarms should clear, and communication will be established.12.2 Co

Section 360−381−S0253.1 NMS Manager Tool BarUser Login/LogoutNMS SystemConfigurationShow equipment as a listReset screenShow equipment as iconsOpen IC

Section 360−381−S0263.2 Configuring the SystemUse this selection to change the supervisor password, and select the equipment communication parameters.

Section 360−381−S027Table 2. Log File TypesFile Name StoresELXXXX.log ICB equipment status changes, user logins and logouts.IADXXXX.log Alarms and lo

Section 360−381−S0284.1.1. Adding/Deleting a UserUse the following steps to add or delete a user. NMS user names and passwords should be limited to te

Section 360−381−S029Use the following steps to insert new ICB equipment:Step Action1. To add equipment within an existing list:Move to the line just b